Cracked Wall : Epoxy Resin F.A.Q.
Structural epoxy injection fills a foundation crack and bonds the concrete back together, restoring strength and stopping future leaks. It's the right choice when the crack has stopped moving. This page helps contractors and homeowners choose the right viscosity, gather supplies and inject a crack correctly.
The Basics
When should I use epoxy instead of polyurethane?
Use epoxy when the crack is dormant (no longer moving) and you want to restore structural strength. If the crack is leaking and may still move with the seasons, use polyurethane.
- Epoxy: Restores structural strength and seals. Cures rigid, so the crack must be dormant. Damp cracks are OK, but flowing water is not.
- Polyurethane: Stops leaks. Cures to a flexible foam that moves with the wall. Works on wet and actively leaking cracks, because water activates it.
How do I know if a crack is still moving?
Signs of movement include a crack that is getting wider, edges that are offset (one side sticks out past the other), or fresh breaks in old paint. If you aren't sure, mark the ends of the crack and check it over a few months, or have a structural engineer look at it.
Will epoxy stop my crack from leaking?
Yes, as long as the crack is completely filled and stays dormant. If the wall moves later, rigid epoxy can't flex, and a new crack may form next to the repair.
What about a bowing wall?
Epoxy repairs the crack but won't stop a wall from bowing. Pair it with carbon fiber, soil anchor plates or wall bracing brackets.
Choosing a Viscosity
Which #1001 epoxy viscosity should I use?
Viscosity means how thick the epoxy is. Thinner epoxy gets into tighter cracks. Thicker epoxy stays put in wider cracks and is less likely to run out the back of the wall.
- #1001 Low Viscosity (16.5 oz): Hairline and tight cracks
- #1001 Low Viscosity, 6.5 oz Universal Cartridge: Small jobs with tight cracks
- #1001 Medium Viscosity (16.5 oz): Typical small cracks
- #1001 High Viscosity (16.5 oz): Wider cracks
- #1001 Extra Heavy Viscosity (16.5 oz): The widest cracks, or where material is running out the back of the wall
What are the specs on #1001 injection epoxy?
- 100% solids, moisture-insensitive epoxy that permanently restores structural strength
- Penetrates cracks wider than 0.005 inches
- Cures on damp or wet surfaces
- 2:1 mix ratio, with no shrinkage
- Bonds to concrete, wood and metal
- Meets ASTM C881, Types I, II, IV and V; Grades 1, 2 and 3; Class B and C
What to Order
What supplies do I need for an epoxy injection job?
- #1001 Injection Epoxy (see above): Fills and bonds the crack.
- Surface Mount Injection Ports: Where you inject. Plan one about every 8 to 12 inches along the crack.
- Surface seal (#602 Surface Seal or #10/35 Anchoring Epoxy): Glues the ports on and seals the face of the crack.
- Convertible Dual Manual Gun: Dispenses the dual cartridges. Convert it to 2:1 for #1001.
- Static mixer (Tapered 1/4" x 32 Element or Step-Down 1/4" x 32 Element) plus a Retaining Nut: Mixes the two parts as they dispense. The retaining nut is sold separately.
Should I use #602 Surface Seal or #10/35 Anchoring Epoxy to seal the crack?
- #602 Surface Seal: A fast-setting, non-structural paste. It's easy to chip off or paint over after the repair. Best for most jobs.
- #10/35 Anchoring Epoxy: A high-strength, non-sag structural epoxy. Use it when you want a structural surface seal, or for anchoring dowels and patching.
Which static mixer do I need?
- Tapered 1/4" x 32 Element or Step-Down 1/4" x 32 Element: Injection epoxy. You can cut the step-down tip to change the bead size.
- 3/8" x 24 Element: High-viscosity liquids
- 1/2" x 18 Element: Gels and pastes
Plan on one mixer per cartridge, plus a few spares. Epoxy cures inside the mixer if you stop for long.
How does the Convertible Dual Manual Gun work?
It comes set up for 300 ml x 300 ml (1:1) cartridges and converts to 300 ml x 150 ml (2:1). It delivers 750 lbs of thrust force with a 22-to-1 mechanical advantage. The push rods are 3/8" case-hardened steel, and the side handle can go on either side.
Installation
How do I inject a crack with epoxy?
- Clean. Wire-brush or grind the face of the crack to remove paint, dirt and efflorescence. Blow out loose debris.
- Set ports. Glue Surface Mount Injection Ports over the crack about every 8 to 12 inches, using #602 or #10/35.
- Seal. Cover the full length of the crack between the ports. Let the seal cure.
- Load. Set the gun to 2:1, load the #1001 cartridge and attach a static mixer. Dispense a little onto scrap until the color is even.
- Inject from the bottom up. Start at the lowest port and inject slowly. When epoxy shows at the next port, move up to that port and repeat to the top.
- Finish. After the epoxy cures, remove the ports. Chip or grind off the surface seal, or paint over it.
Why does epoxy take so long to move up the crack?
Epoxy is thicker than polyurethane and needs time to fill the full depth of the crack. Use slow, steady pressure. Rushing usually means the crack is only filled near the surface.
Can I inject epoxy in a cold basement?
Cold makes epoxy thicker and slows its cure. Store cartridges at room temperature before use and keep the work area warm while it cures.
Can I inject a crack that's wet?
#1001 cures on damp or wet surfaces. If water is actively flowing through the crack, stop it first with polyurethane, or use polyurethane instead.
Shop Epoxy Resin
-
#602 Surface Seal - 22 OZ.
Regular price $42.75 USDRegular priceSale price $42.75 USD -
Retaining Nut For Dual Cartridges
Regular price $1.26 USDRegular priceSale price $1.26 USD -
Surface Mount Injection Port
Regular price $0.80 USDRegular priceSale price $0.80 USD -
Tapered Nozzle 1/4" X 32 Element Static Mixer
Regular price $3.82 USDRegular priceSale price $3.82 USD -
Step-Down Nozzle 1/4" X 32 Element Static Mixer
Regular price $4.15 USDRegular priceSale price $4.15 USD -
#1001 High Viscosity Injection Epoxy 16.5 OZ.
Regular price $34.01 USDRegular priceSale price $34.01 USD -
Convertable Dual Manual Gun
Regular price $128.85 USDRegular priceSale price $128.85 USD -
#1001 Low Viscosity Injection Epoxy 16.5 OZ.
Regular price $34.01 USDRegular priceSale price $34.01 USD