Cracked Wall : Polyurethane F.A.Q.
Polyurethane injection stops water from coming through foundation cracks. It cures into a tough, flexible foam that can move with the wall through the seasons. This page helps contractors and homeowners choose a product, gather the right supplies, and inject a crack correctly.
The Basics
When should I use polyurethane instead of epoxy?
Use polyurethane when stopping water is the goal and the crack may still move with the seasons. Use epoxy when the crack has stopped moving and you need to restore strength.
- Polyurethane: Stops leaks. Cures to a flexible foam that moves with the wall. Works on wet and actively leaking cracks, because water activates it.
- Epoxy: Restores structural strength and seals. Cures rigid, so the crack must be dormant. Damp cracks are OK, but flowing water is not.
Will polyurethane make my wall stronger?
No. Polyurethane seals out water but does not add structural strength. For a bowing wall, see carbon fiber, soil anchor plates or wall bracing brackets.
Does crack injection work on block walls?
Injection works best on poured concrete walls. Concrete block has hollow cores that swallow material, so leaks in block walls usually need a different approach.
Choosing a Product
Which polyurethane should I use?
- Hydro Flex Single Component Polyurethane: Hydrophobic. Expands up to 20 times its volume. Comes in a 10.3 oz caulk cartridge, with no mixing or special gun needed. Good for simple jobs.
- #900 Hydrophilic Injection Urethane (22 oz): Hydrophilic. Expands up to 700%. Best for basement cracks and cold joints.
- #700 Super Low Viscosity Urethane: Hydrophilic. Super-low viscosity for very tight or hairline cracks.
What's the difference between hydrophilic and hydrophobic?
- Hydrophilic (#900, #700) attracts water and reacts with it, quickly foaming into a tough, flexible seal that bonds into the concrete's pores.
- Hydrophobic (Hydro Flex) repels water. It expands when it touches water, then cures into a permanent, flexible, watertight seal.
How do I choose based on crack width?
Thinner material goes deeper into tight cracks. Use #700 Super Low Viscosity on hairline cracks. Use #900 or Hydro Flex on typical shrinkage cracks and cold joints.
What to Order
What supplies do I need for a crack injection job?
- Polyurethane (see above): Seals the crack.
- Surface Mount Injection Ports: Where you inject. Plan one about every 8 to 12 inches along the crack.
- #602 Surface Seal (22 oz, 11 oz caulk tubes, 1/2 gallon or 2 gallon): Glues the ports on and seals the face of the crack so the material can't leak back out.
- Convertible Dual Manual Gun: Dispenses dual cartridges. Not needed for Hydro Flex, which uses a standard caulk gun.
- Static mixer (Tapered 1/4" or Step-Down 1/4") plus a Retaining Nut: Mixes the material as it dispenses. The retaining nut is sold separately.
- Water Dispenser: Adds water to #900 and #700 tubes without removing the bottom plug.
How much material should I buy?
It depends on how wide and deep the crack is. Crack widths vary from top to bottom, so order an extra tube. Running out halfway up a crack is the most common mistake we see.
Installation
How do I inject a crack with polyurethane?
- Clean. Wire-brush the crack and the area around it to remove paint, dirt and efflorescence.
- Set ports. Mark port locations about every 8 to 12 inches along the crack (closer on tight cracks). Glue each Surface Mount Injection Port over the crack with #602 Surface Seal.
- Seal. Cover the full length of the crack between the ports with #602 Surface Seal. Let it set.
- Prepare. Fill #900 or #700 tubes with water using the Water Dispenser, then load the gun and attach a static mixer.
- Inject from the bottom up. Start at the lowest port. Inject until material shows at the next port up, then move to that port and repeat to the top.
- Clean up. After the material has cured, remove the ports. Chip off the #602 Surface Seal or paint over it.
Can I inject a crack that's actively leaking?
Yes. This is where polyurethane works best, because water helps it react and expand. The #602 Surface Seal will grip best if you wipe and dry the face of the crack right before you apply it.
Why is material coming out of the wall somewhere else?
There's a gap in the surface seal, or the crack connects to another crack. Stop, seal the leak with #602, let it set, and continue. Material can also come out the back of the wall into the soil. That's normal on wide cracks.
How should I store polyurethane?
Keep tubes sealed in a cool, dry place until you're ready to use them. Moisture starts the reaction.
Shop Polyurethane
-
#602 Surface Seal - 22 OZ.
Regular price $42.75 USDRegular priceSale price $42.75 USD -
Retaining Nut For Dual Cartridges
Regular price $1.26 USDRegular priceSale price $1.26 USD -
Surface Mount Injection Port
Regular price $0.80 USDRegular priceSale price $0.80 USD -
Tapered Nozzle 1/4" X 32 Element Static Mixer
Regular price $3.82 USDRegular priceSale price $3.82 USD -
Step-Down Nozzle 1/4" X 32 Element Static Mixer
Regular price $4.15 USDRegular priceSale price $4.15 USD -
#900 Hydrophilic Injection Urethane 22 OZ.
Regular price $38.52 USDRegular priceSale price $38.52 USD -
Convertable Dual Manual Gun
Regular price $128.85 USDRegular priceSale price $128.85 USD -
#700 Super Low Viscosity Urethane
Regular price $40.49 USDRegular priceSale price $40.49 USD